- Title:
Introduction to the Internet of Things (IoT) Devices
Course Number:
MCT1201
Course Description:
In this course, students will build a variety of electronic Internet of Things (IoT) projects using the very popular Arduino microcontroller platform and computer code written in C/C++. Students will learn the following topics:
- Electricity and electronic fundamentals (none of the projects exceed the power of a 9 volt battery)
- Reading electronic schematics
- Identify various electronic sensors and actuators (motors and other robotic components)
- Wire their projects using the Arduino compatible processor and a wide range of electronic components
- Write, test, debug C/C++ computer code
- Upload their software to their projects and test its operation.
This course is based on the very popular microcontroller (computer) Arduino platform. Students will build a variety of electronic projects drive by an Arduino compatible processor
Technology Requirements:
Each participant should have the following prior to the start of class.
- Modern computer system (PC, MAC or Chromebook) (desktop / laptop) with some form of IP Camera and either a wired or wireless connection to the home network.
- Highspeed Internet connection (minimum 6Mbps). Check your speed here.
Instructor:
James Bowe, james.bowe@mycompteacher.com, Click here for instructor profile.
Suggested Student Age:
10 to 16 years old
Teaching Method:
This course is an instructor led class using the popular Zoom web-based online meeting application. Each day the instructor will actively lead the class thru two sessions. In the first session, the instructor will present the project for the day, then discuss the prerequisite concepts, skills and introduction to the project components to be used. In the second session, students will then be asked to build their projects with instructor guidance and supervision. Once the project is completed, students will be asked to complete a project worksheet designed document their work and explain in their own words the operation of the device they have built, along with the components used. The worksheet will be submitted to the instructor and graded. Grades along with instructor comments will be shared with the student and parents.
Total Instruction Hours:
30 hours
Available Sections:
MCT1201.002
Starts Monday, August 10th thru Friday, August 21st
2 Weeks, M-F, 2 sessions each day, 9 AM – 12PM
Click Here to Register
MCT1201.003
Starts Saturday, September 12th thru Saturday, November 14th
10 Saturday sessions, from 9AM to 12PM
Registration for this section opens August 13th, 2020
Class Size:
10 Students per section
Cost:
$300 per student, plus $50 for materials
Materials:
Computer / Electronic Kit – Basic
Kit Component List
- 1 pcs UNO R3 Controller Board
- 1 pcs LCD1602 Module ( with pin header)
- 1 pcs Breadboard Expansion Board
- 1 pcs Power Supply Module
- 1 pcs Joystick Module
- 1 pcs IR Receiver
- 1 pcs Servo Motor (SG90)
- 1 pcs Stepper Motor
- 1 pcs ULN2003 Stepper
- Motor Driver Board
- 1 pcs Ultrasonic Sensor
- 1 pcs DHT11 Temperature and Humidity Module
- 1 pcs 9V Battery with DC
- 1 pcs 65 Jumper Wire
- 1 pcs USB Cable 1 pcs
- Active Buzzer
- 1 pcs Passive Buzzer
- 1 pcs Potentiometer
- 1 pcs 5V Relay
- 1 pcs Breadboard
- 1 pcs Remote
- 1 pcs Tilt Switch
- 5 pcs Button (small)
- 1 pcs 1 digit 7-segment Display
- 1 pcs 4 digit 7-segment Display
- 5 pcs Yellow LED
- 5 pcs Blue LED
- 5 pcs Green LED
- 5 pcs Red LED
- 1 pcs RGB LED
- 2 pcs Photo resistor
- 1 pcs Thermistor
- 2 pcs Diode Rectifier (1N4007)
- 2 pcs NPN Transistor (PN2222)
- 1 pcs IC 74HC595
- 120 pcs Resistor
- 10 pcs Female-to-male DuPont Wire